The UNAVCO configuration file for the NetR9 (right click to download. is intended for use with firmware version 5.44
Configuration files for previous firmware versions can be found below.
Note: L2C and L5 tracking is enabled in 5.22 and forward configuration files. For firmware versions preceding 4.93 L2C and L5 tracking were disabled. This change could increase file sizes and bandwidth usage.
We recommend that users who plan to install receivers on public networks utilize IP filtering to increase their network security. IP filtering is disabled by default in this configuration file.
Note #1: After uploading the configuration file you may then enable/disable additional features with caution through the Receiver Configuration menu. Please refer to the user guide, which is available for download on the NetR9 resource page , for additional information regarding configuration.
Note #2: We recommend the use of security features such as password protection and IP filtering that must be carefully configured and applied by each user and are not enabled in this configuration file.
Note #3: GNSS Tracking and Logging (GLONASS, Galileo, BeiDou, QZSS) are not enabled in this configuration.
Note #4: Specific information regarding the configuration of NetR9 for Polar Applications is available at the Remote Station Engineering Page
Elevation Mask:0°
PDOP Mask:99
Horizontal Precision:0.30 [m]
Vertical Precision:0.30 [m]
Clock Steering:Enabled
Everest™ Multipath Mitigation:Disabled
Signal Tracking Bandwidth:Wide
Antenna ID:185
Antenna Type:Zephyr Geodetic 2
Antenna Measurement Method:Antenna Phase Center
Antenna Height:0.0000 [m]
1PPS On/Off:Disabled
External Frequency Available:Undetected
RTK Mode:Low Latency
Receiver Motion:Kinematic
RTK Engine Motion:Kinematic
CMR Input Filter:Disabled
Reference Latitude:0°00’00.00000"N
Reference Longitude:0°00’00.00000"E
Reference Height:0.000 [m]
CMR ID:0
Station Name:NULLNAME
Ethernet IP:192.168.1.2
System Name:Trimble
DNS Resolved Name:----
| Session Name | Sample Rate | Duration | Enabled | Pool | File System | Path Style | Name Style | FTP Push | Email Push |
| DEFAULT | 15 sec | 1440 min | No | Delete when full 1000 MB (~ 1000 days) | Internal | YYYYMM/Session | ##########YYYYMMDDhhmm | No | No |
| A | 30 sec | 1440 min | Yes | Delete when full 2000 MB (~800 days) | Internal | YYYYMM/Session | ##########YYYYMMDDhhmm | No | No |
| B | 1 sec | 60 min | Yes | Delete when full 1500 MB (~36 days) | Internal | YYYYMM/Session | ##########YYYYMMDDhhmm | No | No |
| C | 0.2 Sec | 60 min | yes | Delete when full 1700 0 MB | Internal | YYYYMM/Session | ##########YYYYMMDDhhmm | No | No |
| M | 15 sec | 60 min | yes | Delete when full 50 0 MB | Internal | YYYYMM/Session | ##########YYYYMMDDhhmm | No | No |
| a_ext | 30 sec | 1440 min | No | Delete when full 2000 MB (~800 days) | External | YYYYMM/Session | ##########YYYYMMDDhhmm | No | No |
| b_ext | 1 sec | 60 min | No | Delete when full 2000 MB (~48 days) | External | YYYYMM/Session | ##########YYYYMMDDhhmm | No | No |
Note: The external sessions (a_ext and b_ext) will not log data unless an external drive is plugged into the receiver’s mini usb port and the session is enabled.
| GPS | L1 - CA | Enabled |
| GPS | L2E - L2C and L2E | Enabled |
| GPS | L2C - CM + CL | Enabled |
| GPS | L5 - I + Q | Enabled |
| SBAS | L1 - C/A | Enabled |
| SBAS | L5 | Enabled |
| GLONASS | L1 - C/A | Enabled |
| GLONASS | L1 - P | Enabled |
| GLONASS | L2 - C/A(M) and P | Enabled |
| GLONASS | L3 (Data and Pilot) | Enabled |
| Galileo | E1 | Enabled |
| Galileo | E5 - A | Enabled |
| Galileo | E5 - B | Enabled |
| Galileo | E5 - AltBOC | Enabled |
| BeiDou | E1 | Enabled |
| BeiDou | B2 | Enabled |
| BeiDou | B3 | Enabled |
| QZSS | L1 - C/A | Enabled |
| QZSS | L1 - SAIF | Enabled |
| QZSS | L1C | Enabled |
| QZSS | L2C | Enabled |
| QZSS | L5 | Enabled |
| QZSS | LEX (Pilot) | Enabled |
Article ID: 772
Created: August 17, 2015
Last Updated: February 3, 2022
Author: Henry Berglund
Online URL: https://kb.unavco.org/article/unavco-standard-configuration-file-for-the-netr9-772.html