Use the LINUX command "wvdial SITE", where SITE is the dialer specified in the wvdial.conf file (e.g. [Dialer unavco]). See below.
USRobotics Courier V.Everything Settings:
B0 C1 E0 F1 L2 M1 Q2 V1 X1
BAUD=9600
PARITY=
DIAL=TONE ON HOOK TIMER
&A1 &B0 &C1 &D0 &G0 &H0 &I0 &K1 &L0 &M4 &N6
&P1 &R1 &S0 &T5 &U0 &X0 sY1 %N6 #CID=0
S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002 S07=060
S08=002 S09=006 S10=014 S11=055 S12=050 S13=000 S14=001 S15=000
S16=000 S17=000 S18=000 S19=005 S20=000 S21=010 S22=017 S23=019
S24=150 S25=005 S26=001 S27=000 S28=008 S29=020 S30=000 S31=000
S32=009 S33=000 S34=000 S35=000 S36=000 S37=000 S38=000 S39=000
S40=000 S41=000 S42=125 S43=200 S44=015 S45=000 S46=000 S47=0002
S48=000 S49=000 S50=000 S51=000 S52=000 S53=000 S54=064 S55=000
S56=000 S57=000 S58=000 S59=001 S60=000 S61=010 S62=000 S63=000
S64=000 S65=000 S66=000 S67=000 S68=000 S69=000 S70=000 S71=056
S72=125 S73=121
DIP SWITCHES:
ON: 1,3,4,7,8
################################################################################
C1 E0 F1 M1 Q2 V1 X1
BAUD=9600 PARITY=N WORDLEN=8
DIAL=PULSE ON HOOK TIMER
&A1 &B0 &C1 &D0 &G0 &H0 &I0 &K1 &L0 &M4 &N0
&P0 &R1 &S0 &T5 &U0 &X0 &Y1 %N6 #CID=0
S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002 S07=060
S08=002 S09=006 S10=014 S11=070 S12=050 S13=000 S14=001 S15=000
S16=000 S17=000 S18=000 S190000 S20=000 S21=010 S22=017 S23=019
S24=150 S25=005 S26=001 S27=000 S28=008 S29=020 S30=000 S31=000
S32=009 S33=000 S34=000 S35=000 S36=000 S37=000 S38=000 S39=0001
S40=000 S41=000 S42=126 S43=200 S44=015 S45=000 S46=000 S47=000
S48=000 S49=000 S50=000 S51=000 S52=000 S53=000 S54=064 S55=000
S56=000 S57=000 S58=000 S59=000 S60=000 S61=000 S62=000 S63=000 7
S64=000 S65=000 S66=000 S67=000 S68=000 S69=000 S70=000
DIP SWITCHES:
ON: 1,3,4,7,8
########################################################################################
; Phone = <Target Phone Number>
; Username = <Your Login Name>
; Password = <Your Password>
[Modem0]
Modem = /dev/modem
Baud = 9600
SetVolume = 1
Dial Command = ATDT
Init1 = ATZ
FlowControl = NOFLOW
; Phone = <Target Phone Number>
; Username = <Your Login Name>
; Password = <Your Password>
[Dialer unavco]
Area Code =303
Username = test
Password =test123
Phone = 5551212
Dial Prefix =
Stupid Mode = 1
Inherits = Modem0
# Please read /usr/share/doc/initscripts-*/sysconfig.txt
# for the documentation of these parameters.
USERCTL=yes
PEERDNS=yes
TYPE=Modem
DEVICE=ppp0
BOOTPROTO=dialup
ONBOOT=no
NAME=unavco
CCP=off
PC=off
AC=off
BSDCOMP=off
VJ=off
VJCCOMP=off
LINESPEED=9600
MODEMPORT=/dev/modem
IDLETIMEOUT=600
DEMAND=no
PROVIDER=unavco
DEFROUTE=no
PERSIST=no
PAPNAME=unavco
WVDIALSECT=unavco
MODEMNAME=Modem0
###############################################################################################
Select I/O configuration--> Port configuration
Edit port modem is attached to
Service--> PPP
Baud--> 19200 (or other)
Parameter for PPP mode: Enter the IP addresses
Connection--> modem
# ++ FBCfg v1
# Configuration File, Original Name = PPP
# created Wed Jun 29 17:50:13 UTC 2005
## file /etc/sysconfig/gpssd.config
0 OFF-serial 115200:N:N 0 ppp 1 0
1 serial 115200:N:N 0 ppp 10 0
2 OFF-serial 9600:N:N 0 cmr 10 2
3 OFF-serial 9600:N:N 0 cmr 10 1
## end of file /etc/sysconfig/gpssd.config
## file /etc/sysconfig/met.conf
## end of file /etc/sysconfig/met.conf
## file /etc/sysconfig/advertise
Enable: yes
Interval: 300
Target: 10.234.4.46 16000
Target: 69.44.87.248 16000
## end of file /etc/sysconfig/advertise
## file /etc/sysconfig/dialout
## end of file /etc/sysconfig/dialout
## file /etc/sysconfig/mgetty+sendfax/mgetty.config
#
# mgetty configuration file
#
# this is a sample configuration file, see mgetty.info for details
#
# comment lines start with a "#", empty lines are ignored
# ----- global section -----
#
# In this section, you put the global defaults, per-port stuff is below
# set the global debug level to "4" (default from policy.h)
debug 0
# set the local fax station id
fax-id 49 115 xxxxxxxx
# access the modem(s) with 38400 bps
#speed 38400
# use these options to make the /dev/tty-device owned by "uucp.uucp"
# and mode "rw-rw-r--" (0664). *LEADING ZERO NEEDED!*
#port-owner uucp
#port-group uucp
#port-mode 0664
# use these options to make incoming faxes owned by "root.uucp"
# and mode "rw-r-----" (0640). *LEADING ZERO NEEDED!*
#fax-owner root
#fax-group uucp
#fax-mode 0640
# ----- port specific section -----
#
# Here you can put things that are valid only for one line, not the others
#
# Zoom V.FX 28.8, connected to ttyS0: don’t do fax, less logging
#
#port ttyS0
# debug 3
# data-only y
# some other Rockwell modem, needs "switchbd 19200" to receive faxes
# properly (otherwise it will fail with "timeout").
#
#port ttyS1
# speed 38400
# switchbd 19200
# ZyXEL 2864, connected to ttyS2: maximum debugging, grab statistics
#
#port ttyS2
# debug 8
# init-chat "" ddd+++dddAT&FS2=255 OK ATN3S0=0S13.2=1 OK
# statistics-chat "" AT OK ATI2 OK
# statistics-file /var/log/statistics.ttyS2
# modem-type cls2
# direct connection of a VT100 terminal which doesn’t like DTR drops
#
#port ttyS3
# direct y
# speed 19200
# toggle-dtr n
# SerialPort1
port console
direct y
speed 115200
toggle-dtr n
debug 0
# SerialPort2
port tts/1
direct n
speed 9600
toggle-dtr n
init-chat "" AT OK
debug 0
# SerialPort3
port tts_max0
direct y
speed 115200
toggle-dtr n
debug 0
# SerialPort4
port tts_max1
direct y
speed 115200
toggle-dtr n
debug 0
## end of file /etc/sysconfig/mgetty+sendfax/mgetty.config
## file /etc/sysconfig/ppp/options.console
nocdtrcts
192.168.0.1:192.168.0.10
nocrtscts
local
## end of file /etc/sysconfig/ppp/options.console
## file /etc/sysconfig/ppp/options.tts.1
192.168.0.1:192.168.0.20
nocrtscts
## end of file /etc/sysconfig/ppp/options.tts.1
## file /etc/sysconfig/ppp/options.tts_max0
192.168.0.1:192.168.0.30
nocrtscts
local
## end of file /etc/sysconfig/ppp/options.tts_max0
## file /etc/sysconfig/ppp/options.tts_max1
192.168.0.1:192.168.0.40
nocrtscts
local
## end of file /etc/sysconfig/ppp/options.tts_max1
#############################################################################################
Jun 29 18:30:40 noreaster wvdial[8720]: WvDial: Internet dialer version 1.53
Jun 29 18:30:40 noreaster wvdial[8720]: Initializing modem.
Jun 29 18:30:40 noreaster wvdial[8720]: Sending: ATZ
Jun 29 18:30:40 noreaster wvdial[8720]: OK
Jun 29 18:30:40 noreaster wvdial[8720]: Modem initialized.
Jun 29 18:30:40 noreaster wvdial[8720]: Sending: ATDT3035273541
Jun 29 18:30:40 noreaster wvdial[8720]: Waiting for carrier.
Jun 29 18:30:59 noreaster wvdial[8720]: CONNECT 9600/ARQ
Jun 29 18:30:59 noreaster wvdial[8720]: Carrier detected. Chatmode finished.
Jun 29 18:30:59 noreaster pppd[8707]: Serial connection established.
Jun 29 18:30:59 noreaster /etc/hotplug/net.agent: assuming ppp0 is already up
Jun 29 18:30:59 noreaster pppd[8707]: Using interface ppp0
Jun 29 18:30:59 noreaster pppd[8707]: Connect: ppp0 <--> /dev/modem
Jun 29 18:31:03 noreaster modprobe: modprobe: Can’t locate module ppp-compress-21
Jun 29 18:31:03 noreaster modprobe: modprobe: Can’t locate module ppp-compress-21
Jun 29 18:31:04 noreaster pppd[8707]: Deflate (15) compression enabled
Jun 29 18:31:04 noreaster pppd[8707]: local IP address 10.234.4.32
Jun 29 18:31:04 noreaster pppd[8707]: remote IP address 192.168.0.1
Jun 29 18:31:04 noreaster su(pam_unix)[8760]: session opened for user root by (uid=0)
Jun 29 18:31:04 noreaster su(pam_unix)[8760]: session closed for user root
Jun 29 18:34:48 noreaster pppd[8707]: Terminating on signal 15.
Jun 29 18:34:48 noreaster su(pam_unix)[8812]: session opened for user root by (uid=0)
Jun 29 18:34:48 noreaster su(pam_unix)[8812]: session closed for user root
Jun 29 18:34:48 noreaster pppd[8707]: Connection terminated.
#############################################################################################
Jun 29 17:30:10 KAKA frontpanel[422]: Starting mgettyPort2
Jun 29 17:31:01 KAKA pppd[422]: pppd 2.4.1 started by root, uid 0
Jun 29 17:31:01 KAKA pppd[422]: Using interface ppp0
Jun 29 17:31:01 KAKA pppd[422]: Connect: ppp0 <--> /dev/tts/1
Jun 29 17:31:04 KAKA pppd[422]: Deflate (15) compression enabled
Jun 29 17:31:04 KAKA pppd[422]: local IP address 192.168.0.1
Jun 29 17:31:04 KAKA pppd[422]: remote IP address 10.234.4.32
Jun 29 17:31:10 KAKA AutoDelete: Searched 1330 files in 109 directories.
Jun 29 17:31:37 KAKA Advertise[251]: Sending Advertisements.
Jun 29 17:32:11 KAKA AutoDelete: Searched 1330 files in 109 directories.
Jun 29 17:33:11 KAKA AutoDelete: Searched 1330 files in 109 directories.
Jun 29 17:34:11 KAKA AutoDelete: Searched 1330 files in 109 directories.
Jun 29 17:34:48 KAKA pppd[422]: LCP terminated by peer (User request)
Jun 29 17:34:51 KAKA pppd[422]: Connection terminated.
Jun 29 17:34:51 KAKA pppd[422]: Connect time 3.8 minutes.
Jun 29 17:34:51 KAKA pppd[422]: Sent 75 bytes, received 87 bytes.
###############################################################################################
Article ID: 32
Created: January 13, 2009
Last Updated: January 13, 2009
Author: Freddy Blume
Online URL: https://kb.unavco.org/article/trimble-netrs-how-to-set-up-a-ppp-connection-to-a-netrs-using-linux-and-wvdial-32.html