| UNAVCO
 


Knowledge Base

Vaisala - How to integrate the Vaisala WXT510/520 with the Trimble NetRS/NetR9

How to integrate the Vaisala WXT510/520 and the Trimble NetRS/NetR9

Configuring the Vaisala WXT510/520 Weather Transmitter

There are two ways to configure the Vaisala WXT510/520 Weather Transmitter:

  1. Use the Vaisala configuration software and service cable; load the UNAVCO configuration file located at:
    http://kb.unavco.org/kb/questions/306/Vaisala+WTX-510%7B47%7D520+config+file+.

  2. OR

  3. Use hyper terminal (or any other terminal emulation program) to configure the Vaisala WXT510/520 manually.

To configure the Vaisala using a terminal emulation program:

  1. Connect to the Vaisala using the following settings:

    • Baud: 19200

    • Parity: None

    • Flow Control: None

    • Edit the hyper terminal ASCII settings:

      • check box for "send line ends for line feed"

      • check box for "Echo typed characters locally"

      • check box for "Append line feed to incoming line ends"

  2. With the terminal connection established, power up the Vaisala. You should get a "0X0, start" message.

  3. Use the following commands to configure the WXT510/520:

    • 0XU,M=Q,C=2   (This should set the WXT510 to NMEA polled, RS232 communication)

    • 0TU,R=&11010000,I=180,P=B,T=C   (This should set the pressure units to bar and temperature to Celsius)

    • 0RU,R=&10000000U=M,Z=A   (This sets the precipitation units to mm/hr and counter reset)

    • 0WU,R=&01001000 (These next two commands  sets wind averaging, units, and output values)

    • 0WU, I=180,A=180,U=M,F=1 

    • 0SU,R=&00000000   (This removes the system status elements from the output values)

    • 0XU,M=P (to change the communication protocol back to ASCII)
  4.  

  5. Verify the Vaisala is enabled:

    • Issue a "0R0" command.

    • The met pack is set to output the following string:

      0R0,Dm=076D,Sm=0.1M,Ta=24.4C,Ua=20.9P,Pa=0.8429B,Rc=0.00M,Hc=0.0M

      where:

      0R0 - the command that is sent
      Dm - wind direction, degrees
      Sm - wind speed, m/s
      Ta - temperature, degree C
      Ua - humidity, percent
      Pa - barometric pressure, Bar
      Rc - rainfall, mm/sampling period (reset at each measurement)
      Hc - hail, hits/sampling period (reset at each measurement)

Configuring the NetRS/NetR9

Configure the NetRS as follows:

  • I/O Configuration

    • Serial Port 2 Configuration

      • Service: Met-Tilt

        Baud: 19200
        Parity: None
        Flow Control: None

        Parameters for Met-Tilt mode:

        Command 0R0
        Schedule set to desired sample interval

Using teqc to extract met records

Use the following command to create a met file:

teqc +met $filename.met -M.obs pr+td+hr+ws+wd+ri+hi $filename.dat > $filename.obs

where $filename.dat is the file you’ve created using the .T00 file you pulled from the receiver.

Alternatively, if you are collecting BNX data, use:

teqc +met $filename.met -M.obs pr+td+hr+ws+wd+ri+hi -binex  $filename.BNX > $filename.obs

 

jn2009

Attached Files
There are no attachments for this article.
Comments (2)
Comment by fabio on Thu, Jan 15th, 2015 at 11:55 PM
I connect the WXT to a PC tru hyperterminal and i get a message all ready and dont let me configurate the sensor. how i stop or reset the sensor tru hyperterminal,
Comment by fabio on Thu, Jan 15th, 2015 at 11:54 PM
I connect the WXT to a PC tru hyperterminal and i get a message all ready and dont let me configurate the sensor. how i stop or reset the sensor tru hyperterminal,
Name
Email
Security Code Security Code
Related Articles RSS Feed
How to Mount a Vaisala WXT 520 Met Pack
Viewed 6337 times since Mon, Dec 20, 2010
Vaisala Weather Transmitter WXT510 User's Guide (July 2005)
Viewed 1709 times since Fri, Nov 20, 2009
Vaisala Weather Transmitter WXT520 User's Guide (2008)
Viewed 1409 times since Mon, Feb 1, 2010
Vaisala Weather Transmitter WXT510 Product Brochure and Specification Sheet
Viewed 2127 times since Wed, Feb 18, 2009
Vaisala - How to configure a Trimble NetRS for use with a Vaisala WXT510 metpack in the Plate Boundary Observatory
Viewed 7436 times since Fri, Nov 20, 2009
WXT520 Ordering guide
Viewed 2201 times since Mon, Mar 24, 2014
How to integrate the Vaisala WXT510/520 and the Septentrio PolaRx5 (Command Line)
Viewed 2822 times since Fri, Jan 8, 2016
Vaisala WTX510/520 configuration file
Viewed 4955 times since Wed, Jul 1, 2009
Vaisala WXT-520 important service notice
Viewed 5950 times since Wed, Jun 12, 2013
Vaisala - How to integrate the Vaisala WXT520 with the Ashtech MicroZ
Viewed 5789 times since Tue, Jan 26, 2010
MENU
 

Last modified: 2019-12-27  16:36:35  America/Denver