| UNAVCO
 


Knowledge Base

Trimble R-Utilities

Trimble R-Utilities

No longer supported by Trimble. Trimble R-Utilities is a group of programs that permit remote control of certain Trimble GPS receivers. R-Utilities provide receiver configuration capability via direct serial, phone modem, and wireless radio protocols. The latest version of R-Utilities for Windows, LINUX, and Solaris should be able to translate R00, T00, and T01 files. (Please let us know if you encounter a problem by sending an email to support at unavco.org.) Note that the R-Utilities can not be used to download a NetRS GPS receiver, only to translate the T00 file acquired from the receiver.

Trimble’s Latest RUNPKR00 program that converts T00/T01 Files to DAT is not embedded in R-Utilities. The Trimble runpkr00 program allows users to extract .DAT or .TGD files  from R00/T00/T01 files logged by Trimble GPS/GNSS receivers.  Note that  for GNSS signals to be extracted from "Record Type 27" (RT27) files the  "-g" flag must be added to the command line, which will produce a .TGD  file.  Both .DAT and .TGD files can then be interpreted by teqc. [Windows v2.36] [Linux v2.44] [Solaris SPARC v2.44] [Solaris x86 v2.44]

The following table gives the operating system and receiver types supported for each version of the R-Utilities software. Click on the version number to download.

Operating System 4000 Rxs 4700 Rxs 5700 / R7   RHL 6.x RHL 7.x RHL 9.x
Linux v2.55 (T00/T01/R00) X   X     X X
Linux v2.51 X   X     X  
Linux v2.42 X X     X    
Linux v2.35 X       X    
Solaris v2.53 X   X   n/a n/a n/a
Windows v2.55 (T00/T01/R00) X   X   n/a n/a n/a

[Trimble R-Utilities User’s Guide (pdf)(2004)]

Attached Files (12)
Comments (1)
Comment by Benedetto Porfidia on Tue, May 30th, 2017 at 2:06 PM
Dear Sirs Within a wide research program focused on geodesy of Italy, I‘m trying to couple a Trimble 5700 receiver with a raspberry pi A+ sbc to make a standalone permanent GPS station supplied by solar cells and batteries. The choice of the type of sbc is due to its power consumption, but it runs only Linux binaries compiled for arm CPU architecture. I was planning to use your R-Utils for Trimble receivers to interface with it. Can you suggest me how to make R-utils running on that platform? Best regards and thanks in advance Benedetto Porfidia
Name
Email
Security Code Security Code
Related Articles RSS Feed
Trimble Geomatics Office - How to apply precise orbits in TGO
Viewed 6709 times since Tue, Feb 2, 2010
Trimble Geomatics Office - How to process fast-static and post-processing kinematic surveys using TGO
Viewed 54573 times since Tue, Jan 26, 2010
Trimble Geomatics Office - TGO User Notes
Viewed 25567 times since Fri, Jan 15, 2010
Trimble WinFlash - How to load new firmware onto the Trimble 4700 receiver
Viewed 19948 times since Mon, Dec 14, 2009
Trimble R7/5700 - How to verify receiver tracking using Trimble GPS Configurator software
Viewed 9010 times since Tue, Jan 26, 2010
Trimble Remote Controller v2.21
Viewed 21223 times since Fri, Feb 6, 2009
Trimble Geomatics Office - Importing RINEX 2.11 data files
Viewed 10183 times since Thu, Jul 7, 2011
Trimble 5700/R7 - How to configure the receiver using Trimble Configuration Toolbox software
Viewed 22125 times since Tue, Jan 26, 2010
Trimble GPS Configurator (all versions)
Viewed 32738 times since Fri, Sep 24, 2010
How to download a Trimble receiver using the Trimble rfile program
Viewed 4363 times since Thu, Jul 30, 2009
MENU

Last modified: Monday, 12-May-2014 00:18:29 UTC