| UNAVCO
 


Knowledge Base

Trimble R-Utilities

Trimble R-Utilities

No longer supported by Trimble. Trimble R-Utilities is a group of programs that permit remote control of certain Trimble GPS receivers. R-Utilities provide receiver configuration capability via direct serial, phone modem, and wireless radio protocols. The latest version of R-Utilities for Windows, LINUX, and Solaris should be able to translate R00, T00, and T01 files. (Please let us know if you encounter a problem by sending an email to support at unavco.org.) Note that the R-Utilities can not be used to download a NetRS GPS receiver, only to translate the T00 file acquired from the receiver.

Trimble’s Latest RUNPKR00 program that converts T00/T01 Files to DAT is not embedded in R-Utilities. The Trimble runpkr00 program allows users to extract .DAT or .TGD files  from R00/T00/T01 files logged by Trimble GPS/GNSS receivers.  Note that  for GNSS signals to be extracted from "Record Type 27" (RT27) files the  "-g" flag must be added to the command line, which will produce a .TGD  file.  Both .DAT and .TGD files can then be interpreted by teqc. [Windows v2.36] [Linux v2.44] [Solaris SPARC v2.44] [Solaris x86 v2.44]

The following table gives the operating system and receiver types supported for each version of the R-Utilities software. Click on the version number to download.

Operating System 4000 Rxs 4700 Rxs 5700 / R7   RHL 6.x RHL 7.x RHL 9.x
Linux v2.55 (T00/T01/R00) X   X     X X
Linux v2.51 X   X     X  
Linux v2.42 X X     X    
Linux v2.35 X       X    
Solaris v2.53 X   X   n/a n/a n/a
Windows v2.55 (T00/T01/R00) X   X   n/a n/a n/a

[Trimble R-Utilities User’s Guide (pdf)(2004)]

Attached Files (12)
Comments (1)
Comment by Benedetto Porfidia on Tue, May 30th, 2017 at 2:06 PM
Dear Sirs Within a wide research program focused on geodesy of Italy, I‘m trying to couple a Trimble 5700 receiver with a raspberry pi A+ sbc to make a standalone permanent GPS station supplied by solar cells and batteries. The choice of the type of sbc is due to its power consumption, but it runs only Linux binaries compiled for arm CPU architecture. I was planning to use your R-Utils for Trimble receivers to interface with it. Can you suggest me how to make R-utils running on that platform? Best regards and thanks in advance Benedetto Porfidia
Name
Email
Security Code Security Code
Related Articles RSS Feed
Trimble Configuration Toolbox (all versions)
Viewed 63385 times since Fri, Sep 24, 2010
Trimble 5700/R7 - How to configure the receiver using Trimble Configuration Toolbox software
Viewed 22362 times since Tue, Jan 26, 2010
Trimble Geomatics Office - TGO User Notes
Viewed 25609 times since Fri, Jan 15, 2010
Trimble Geomatics Office - How to apply precise orbits in TGO
Viewed 6752 times since Tue, Feb 2, 2010
Trimble Geomatics Office - TGO v1.6 Rev.A, April 2002, User Guide
Viewed 2458 times since Fri, Jan 15, 2010
Trimble TRIM4000 Download Software for DOS
Viewed 3003 times since Fri, Jul 31, 2009
Trimble R7/5700 - How to verify receiver tracking using Trimble GPS Configurator software
Viewed 9120 times since Tue, Jan 26, 2010
Trimble Geomatics Office - Importing RINEX 2.11 data files
Viewed 10235 times since Thu, Jul 7, 2011
Trimble GPSurvey V2.35 - How to process GPS data (outline) (historical)
Viewed 11750 times since Fri, Jan 9, 2009
Trimble Convert to RINEX Utility v2.1.1.0
Viewed 109561 times since Tue, May 17, 2011
MENU

Last modified: Monday, 12-May-2014 00:18:29 UTC