| UNAVCO
 


Knowledge Base

How to configure a RAD master-slave modem pair

How to configure a RAD master-slave modem pair

General Information

RAD modems can be used to extend an Ethernet connection over a 4-wire copper cable for a distance of up to 4 miles.


Figure 1: Working configuration of a slave-master RAM modem pair.

The two modems have a Master-Slave relationship. New modems out of the box have no Master or Slave setting; for our uses we have assigned the modem closest to the computer to be the Master modem and the one closest to the internet hub the Slave modem. To get the modems to work requires the following:

  1. Set up the modems as shown in Figure 2 (below).

  2. Configure one modem to be Master.

  3. Configure the other modem to be Slave.

Note: Before shipping:

  1. Reset user name and password to match the computer (the symbols & or @ are not allowed).

  2. Clear log tables.

Configuration of the Master modem

To configure the Master modem, set up the modem as shown in Figure 2 (below).



Figure 2: Set-up for configuration of the Master modem.

Connect the serial cable from the serial port on the back of the modem to port ttyS* on the back of the computer (where * represents the serial port number). Now open a terminal window and type:

[root@hostname]# ~]# cu -l /dev/ttyS0

(Note that in order for this command to be executed you must have cu installed. In Fedora, the rpm that provides cu is uucp.) The above command will take you into the configuration menu of the RAD modem.

ASMi-52

USER NAME:|
PASSWORD:


ESC - clear; & - exit; @ - scroll
------------------------------------

To access the modem you will need to enter a USER NAME and a PASSWORD. All modems out of the box have the following USER NAME and PASSWORD scheme:

WARNING! Never use the symbols & and @ when assigning user names and password to these modems.

USER NAME = < none just hit enter here >
PASSWORD = 1234

After you log in you will be in the Main Menu:

ASMi-52

Main Menu

1. Inventory >
2. Configuration >
3. Monitoring >
4. Diagnositics >
5. File Utilities >

> |


ESC - prev. menue; ! - main menu; & - exit; @ - scroll
--------------------------------------------------------

Navigating through the menu is quite simple. To move forward within each menu option, enter the numbers that correspond to the menu options you see. To move backwards through the menu options, use the Esc key.

First, set the Master Clock setting. This setting governs whether the modem is a Master modem or a Slave modem. In the Master Clock menu you have two choices: "Receive" and "Internal."

Giving a modem a Master Clock setting of "Internal" will make it a Master modem.

Giving a modem a Master Clock setting of "Receiver" will make it a Slave modem.

To get to the Master Clock menu from the Main Menu, go into Configuration:

ASMi-52

Configuration

1. System Configuration >
2. SHDSL Configuration >
3. LAN Configuration >

> 1


ESC - prev. menue; ! - main menu; & - exit; @ - scroll
--------------------------------------------------------

Choose System Configuration from within the Configuration menu.

ASMi-52

Configuration > System Configuration

1. Master Clock > (Internal)
2. Low Speed E1 Operation (NO)
3. Management >
4. Control Port >
5. Factory Default >
6. Reset >
7. Save

> 1


ESC - prev. menue; ! - main menu; & - exit; @ - scroll
--------------------------------------------------------

Choose Master Clock from within the System configuration menu.

ASMi-52

... > System Configuration > Master Clock (Internal)

1. Receive
2. Internal

> 2


ESC - prev. menue; ! - main menu; & - exit; @ - scroll
--------------------------------------------------------

To make this modem the Master, type 2 at the command prompt and then hit Enter. This will take you back into the System Configuration menu. To save the new setting, type 7 and hit Enter. Our modem is now a Master modem. To get back to the main menu, hit the Esc key. You may have to do so several times.

Use the same sequence of menu options to set the second modem to be the Slave modem. The only two differences are:

  1. Switch the serial cable from the back of the Master modem to the modem that will be the Slave modem. See Figure 3.

  2. In the Master Clock options, choose "Receive" instead of "Internal," and then Save.


Figure 3: Set-up for configuration of the Slave modem.

After saving the "Receive" setting for the Master Clock setting on the Slave modem, the two modems will go through a sequence of light blinking. Once they are done each modem will have three green lights in the front, which means the two modems are now working properly.

Configure User Name and Password

User name and password can be set from the Terminal menu.

From the Main Menu, select Configure > System Configuration > Control Port > Port Control > Terminal.

ASMi-52

... > Port Control > Terminal

1. Change Access >
2. POP ALARM (NO)
3. Security TimeOut (10 min)
4. Save

> 1


ESC - prev. menue; ! - main menu; & - exit; @ - scroll
--------------------------------------------------------

Select Change Access.

ASMi-52

Change Access

1. User Name ...()
2. Password ...
3. Clear User Name ...
4. Clear Password ...

> 1


ESC - prev. menue; ! - main menu; & - exit; @ - scroll
--------------------------------------------------------

To enter a new user name, type 1 and hit the Enter key. To enter a new password, type 2 and hit the Enter key. You must save any changes you make. Go back to the Terminal menu by hitting the Escape key, and save the new user name and password.

Clearing Log Files

Before shipping, it is a good idea to clear all log files in each of the modems. To do this, start from the Main Menu page and follow this sequence of menu options: Monitoring (3) > System Monitoring (2).

You should now be in the System Monitoring menu:

ASMi-52

Monitoring > System Monitoring

1. System Status []
2. System Log File []
3. System Clear Log File

> |


ESC - prev. menue; ! - main menu; & - exit; @ - scroll
--------------------------------------------------------

Type 3 and then hit the Enter key to clear log files; type "Y" to confirm the clearing of the log files.

Setting the IP address and Manager Control

When the remote site has free IP address we can assign one to the Master modem and have access to it via a web browser. The IP address is given to the modem in the Management menu. To get to the Management menu, start from the Main menu and choose the following sequence of menu options: Configure (2) > System Configuration > Management (3).

ASMi-52

... > System Configuration > Management

1. Device Info >
2. Host IP >
3. Manager List >
4. Management Access >
5. MTU[64 - 1540] ...(1540)
6. VLAN Encapsulation >
7. Save

> |


ESC - prev. menue; ! - main menu; & - exit; @ - scroll
--------------------------------------------------------

In the Management menu we need to configure two options:

  • Host IP

  • Manager List

To configure the Host IP, type 2 and hit the Enter key. You will now find yourself in the following window:

ASMi-52

... > Management > Host IP

1. Host IP address ...(0.0.0.0)
2. Host IP mask ...(0.0.0.0)
3. Host default gateway ...(0.0.0.0)
4. Read community ...(public)
5. Write community ...(public)
6. Trap community ...(public)
7. Save

> |


ESC - prev. menue; ! - main menu; & - exit; @ - scroll
--------------------------------------------------------

Here you will need to enter a Host IP address, a Host IP mask and a Host default gateway. To enter the Host IP address, type 1 and hit the Enter key; you can now type in an IP address that is assigned to this modem. When you are done, hit the Enter key; this will put your cursor to the right of the ">". Now do the same for Host IP mask and Host default gateway. When you are done, hit the Esc key and Save.

To configure the Manager list, type 3 and hit the Enter key. The IP addresses on this list are the only ones that are allowed to log into the modem and make changes. We can specify up to 10 IP addresses. Each IP address has a corresponding network mask that must also be specified. You can enter these addresses in the same way we entered the Host IP addresses above.

ASMi-52

... > Management > Host IP

1. MNG 1 IP ...(0.0.0.0)
2. MNG 2 IP ...(0.0.0.0)
3. MNG 3 IP ...(0.0.0.0)
4. MNG 4 IP ...(0.0.0.0)
5. MNG 5 IP ...(0.0.0.0)
6. MNG 6 IP ...(0.0.0.0)
7. MNG 7 IP ...(0.0.0.0)
8. MNG 8 IP ...(0.0.0.0)
9. MNG 9 IP ...(0.0.0.0)
10. MNG 10 MASK ...(0.0.0.0)
11. MNG 1 MASK ...(0.0.0.0)
12. MNG 2 MASK ...(0.0.0.0)
13. MNG 3 MASK ...(0.0.0.0)
14. MNG 4 MASK ...(0.0.0.0)
15. MNG 5 MASK ...(0.0.0.0)
16. MNG 6 MASK ...(0.0.0.0)
17. MNG 7 MASK ...(0.0.0.0)
18. MNG 8 MASK ...(0.0.0.0)
19. MNG 9 MASK ...(0.0.0.0)
20. MNG 20 MASK ...(0.0.0.0)

> |


ESC - prev. menue; ! - main menu; & - exit; @ - scroll
--------------------------------------------------------

Again, when you are done, hit the Esc key and Save. Now you are able to configure the modem via the internet by entering the following address into a web browser:

http:// < ip number assigned to the Master modem >

Set up the modems in between any internet connection to check that they work properly before shipping out to a site.

Attached Files
There are no attachments for this article.
Comments (15)
Comment by sultan on Sun, Feb 8th, 2015 at 2:19 PM
Friends help set up properly this modem) Three green light came on and another red light ALM) drove more according to your instruc but did not get) pozhaluista tell all as detailed as possible so that I found my mistake) and IP address propisysat both modem), and if not proskrinshotit hard as it should be
Comment by leased line on Sun, Nov 30th, 2014 at 7:54 PM
Very good teaching method. Because "How to configure a RAD master-slave modem pair" this full post very effective and you did a great job where you add screenshot. Thanks buddy.
Comment by govind singh on Tue, Sep 30th, 2014 at 12:28 PM
Requirement for step by step modem configuration file
Comment by praveer on Fri, Jul 18th, 2014 at 2:42 PM
very very informative and thanks a lot.its working absolutely fine.can you please help me out to how to configure a CT-200GTA modems.thanking you once again.
Comment by rajendra kumar on Thu, Nov 14th, 2013 at 8:51 AM
sir i want to configure modem for internet lease line please send me whole document by mail or phone comunicatin 8400000946
Comment by Monu Rajput on Mon, Jun 24th, 2013 at 10:05 AM
Dear sir/madam I have a one pair Raid asmi52 E1 Modem and i want to use this modem as a LAN Extender.. plz help me...as soon as possible.... Thanks
Comment by Solomon on Thu, May 2nd, 2013 at 2:59 PM
I have asmi 52 rad modem I want to clear the password And IP address but I forgot it the password and IP address What can I do
Comment by arun potphode on Sat, Feb 16th, 2013 at 8:36 AM
pls send me settings
Comment by arun potphode on Sat, Feb 16th, 2013 at 8:32 AM
pls send me settings
Comment by Dilip Pandey on Tue, Feb 5th, 2013 at 8:37 AM
Very good article, Kindly share the extra steps to set the Timeslots (for 512, 768K etc.) at master modem.
Comment by narendra on Mon, Oct 22nd, 2012 at 10:13 AM
how to configure asmi 52 modem in bsnl leade line using airtel media.
Comment by ratha hun on Fri, Aug 12th, 2011 at 7:42 AM
Dear Sir, In my Red Modem ASMi-52 can’t log in, i try to use default password but still cannot. so please show the step how to reset password on it. Thanks you in advance!!!
Comment by navy on Fri, Aug 12th, 2011 at 6:57 AM
i want you show me modem Rad Asmi-52. what can’t log in to modem rad, what can i do? cos i can’t log in to modem i don’t put username:, but i put password:1234 already? i can’t log in too. i want you u show me,ok?
Comment by Hemant Sawant on Mon, Dec 20th, 2010 at 7:36 AM
In case of Lease line we keep clock settings as "Internal" but in case of PRI lines we need to keep it as "External IR". Very good step by step info is provided..very useful.Thnks Regards, Hemant Sawant
Comment by Vlad on Tue, Nov 24th, 2009 at 8:39 AM
Thank you very much! It’s good training for begining users!
Name
Email
Security Code Security Code
Related Articles RSS Feed
MENU

Last modified: Monday, 12-May-2014 00:18:29 UTC